Home / LEV Testing / Guide
LEV testing - woodworking dust
Wood dust is not just mess - it is a health hazard, and hardwood dust is a known carcinogen. So a woodworking dust extraction unit is a piece of health-protection equipment, and buying the right one means it has to actually capture the dust the machines produce. Here is what to consider when choosing a dust extraction unit for woodworking - and why capture, not just collection, is the point.
The short answer
Buying a dust extraction unit for woodworking means choosing one that genuinely captures the wood dust at the machines, because wood dust is a health hazard - softwood dust causes asthma and respiratory disease, and hardwood dust is a Group 1 carcinogen linked to nasal cancer, with workplace exposure limits of 5 mg/m3 for softwood and 3 mg/m3 for hardwood dust (8-hour average). Key considerations: enough airflow (volume and suction) to capture the dust at the machines it serves; the right transport velocity in the ducting to keep the dust moving without settling; adequate filtration to clean the extracted air, ideally to a fine standard given the fine dust is the most harmful; and capacity and connection suited to the machines and how many run at once. And crucially, a dust extraction unit is LEV controlling a health hazard, so it must be maintained and given a thorough examination and test - normally at least every 14 months - to prove it keeps capturing. So the buyer's job is to choose a unit that captures effectively, and to remember that buying it is only the start: it has to be kept working and tested.
Wood dust is a health hazard
The starting point for buying woodworking dust extraction is understanding that wood dust is a genuine health hazard, so the extraction is health-protection equipment, not just housekeeping. Wood dust, breathed in over time, causes respiratory disease: softwood dust can cause asthma and other respiratory conditions, and hardwood dust is more serious still - it is classified as a Group 1 carcinogen, known to cause cancer in humans, linked in particular to nasal cancer among woodworkers. So the fine dust produced by sawing, sanding and machining wood is something workers must be protected from breathing, which is what the dust extraction is for.
This is reflected in the workplace exposure limits: the limit for softwood dust is 5 mg/m3 and for hardwood dust 3 mg/m3, as eight-hour time-weighted averages, and where hardwood and softwood are mixed, the lower hardwood limit applies to the total. These limits are what the extraction has to help keep exposure below. So buying a dust extraction unit is buying a means of controlling a health hazard to within legal limits - which frames the whole purchase: the unit has to actually capture the dust well enough to protect the workers and meet the limits, not merely collect some of it. A unit that looks like it extracts but does not capture the dust effectively fails at its actual purpose. Understanding that wood dust is a real hazard, hardwood especially, is what makes clear why capture, not just collection, is what a buyer should be choosing for.
Capture, airflow and velocity
The core of choosing a dust extraction unit is that it must capture the dust at the machines - and that comes down to airflow and velocity. The unit needs enough airflow - volume and suction - to draw the dust in at each machine it serves, capturing it at source before it escapes into the workshop air. Different machines produce different amounts of dust and need different airflows, and a unit has to provide enough for the machines connected to it, allowing for how many run at once. An underpowered unit, or one serving too many machines, will not pull enough air at each to capture the dust properly, letting it escape - so matching the airflow to the machines is central.
Alongside airflow, the transport velocity in the ducting matters: the air in the ducts has to move fast enough to keep the captured wood dust moving along to the unit without settling out inside the ducts. Wood dust, being relatively heavy, needs a good conveying velocity, or it drops out and builds up in the ductwork, blocking it and reducing the capture. So the ducting has to be sized and run to maintain the transport velocity - not too large, or the velocity drops. Together, adequate airflow at the machines and adequate transport velocity in the ducts are what make the unit actually capture and convey the dust - which is the real job. A buyer should look past the headline that a unit extracts, to whether it provides the airflow and velocity to capture the dust at the specific machines it will serve. That is what determines whether it protects the workers.
Filtration and capacity
Two more considerations round out the choice: filtration and capacity. Filtration matters because the extracted air, once the dust is captured, is usually cleaned and often returned to the workshop or discharged - and the filtration determines how well the fine dust is removed from that air. This is important because the finest wood dust is the most harmful to breathe, penetrating deepest into the lungs, so a unit's filtration should be good enough to remove the fine dust effectively, not just the coarse. A unit with poor filtration may capture the dust from the machine only to return the finest, most harmful fraction to the workshop air - so the filtration standard is a real consideration, especially where the air is recirculated.
Capacity - how much dust the unit can hold before it needs emptying, and how it collects it - matters for practicality: a unit has to have the capacity to handle the volume of dust the workshop produces without constant emptying, and a sensible collection arrangement (bags, bins, or a larger system) suited to the scale. This is more about workability than health, but a unit that is impractical to keep emptied may end up run past capacity, where its performance drops. So capacity should suit the workshop's output. Together, filtration and capacity complete the picture alongside capture: the unit must capture the dust (airflow and velocity), clean the air well (filtration, especially of the fine dust), and hold the dust practically (capacity). A buyer weighing these against the machines and workshop is choosing a unit that will actually do the health-protection job.
Buying it is only the start
A crucial point for any buyer is that buying the dust extraction unit is only the start - because it is local exhaust ventilation controlling a health hazard, so it carries ongoing duties. Under COSHH, LEV controlling a hazardous substance must be maintained in effective working order and given a thorough examination and test at suitable intervals, normally at least every 14 months. So a woodworking dust extraction unit has to be kept maintained and tested throughout its life to prove it keeps capturing the dust - it is not a fit-and-forget purchase. The best unit, bought and installed, still has to be maintained and tested to keep protecting the workers and meeting the duty.
This matters for the buyer because it means the choice should factor in maintainability and testability, and the commitment is ongoing, not one-off. A unit's performance degrades over time - filters load, the fan wears, ducts can partly block - so without maintenance and testing, a unit that captured well when installed may quietly stop doing so, leaving workers exposed while it appears to run. The thorough examination and test catches that, verifying the unit still captures the dust adequately. So a buyer should understand that they are taking on not just a piece of equipment but a duty to keep it working and prove it does - and choose accordingly, and plan for the ongoing testing and maintenance. Buying a good unit is necessary but not sufficient: keeping it tested and maintained is what makes it go on protecting the workers, which is the whole point of buying it. The purchase starts the protection; the upkeep and testing sustain it.
The takeaway
A woodworking dust extraction unit is health-protection equipment, because wood dust is a health hazard - softwood dust causing asthma and respiratory disease, hardwood dust a Group 1 carcinogen linked to nasal cancer, with exposure limits of 5 mg/m3 softwood and 3 mg/m3 hardwood to be kept below. So buying one means choosing a unit that genuinely captures the dust at the machines: enough airflow to capture at each machine it serves, the right transport velocity in the ducting to keep the dust moving without settling, adequate filtration to remove the fine dust that is most harmful, and capacity suited to the workshop's output. Capture, not just collection, is what a buyer should be choosing for.
And crucially, buying the unit is only the start. It is LEV controlling a health hazard, so it must be maintained in effective working order and given a thorough examination and test, normally at least every 14 months, to prove it keeps capturing - it is not fit-and-forget. A unit's performance degrades unnoticed without upkeep, so the best unit still has to be maintained and tested to keep protecting the workers. So the buyer's job is twofold: choose a unit that captures effectively at the specific machines, and plan for the ongoing maintenance and testing that keeps it doing so. Choose for capture, plan for upkeep - and the unit does the health-protection job it is bought for, throughout its life, not just when new.
Questions
Because wood dust is a health hazard, not just mess. Softwood dust causes asthma and respiratory disease, and hardwood dust is a Group 1 carcinogen linked to nasal cancer among woodworkers. The workplace exposure limits are 5 mg/m3 for softwood and 3 mg/m3 for hardwood dust (8-hour average). So dust extraction is health-protection equipment that has to capture the dust to keep exposure below the limits.
That it actually captures the dust at the machines - which comes down to enough airflow to draw the dust in at each machine it serves, and the right transport velocity in the ducting to keep the dust moving without settling. A buyer should look past the headline that a unit extracts to whether it provides the airflow and velocity to capture the dust at the specific machines it will serve.
Because the extracted air is usually cleaned and often returned to the workshop or discharged, and the filtration determines how well the fine dust is removed. The finest wood dust is the most harmful to breathe, so filtration should be good enough to remove it effectively - otherwise a unit may capture the dust from the machine only to return the finest, most harmful fraction to the air, especially where it recirculates.
Capacity - how much dust the unit holds before emptying, and how it collects it - matters for practicality. A unit needs the capacity to handle the workshop's dust output without constant emptying, with a sensible collection arrangement for the scale. A unit that is impractical to keep emptied may end up run past capacity, where its performance drops, so capacity should suit the output.
Yes. It is LEV controlling a health hazard, so under COSHH it must be maintained in effective working order and given a thorough examination and test at suitable intervals - normally at least every 14 months - to prove it keeps capturing the dust. It is not a fit-and-forget purchase: the best unit still has to be maintained and tested to keep protecting the workers.
Because a unit's performance degrades over time - filters load, the fan wears, ducts can partly block - so a unit that captured well when installed may quietly stop doing so, leaving workers exposed while it appears to run. Maintenance keeps it working, and the thorough examination and test verifies it still captures the dust. Buying starts the protection; upkeep and testing sustain it.
A woodworking dust extraction unit is LEV controlling a carcinogen - our thorough examination and test proves it keeps capturing the dust, the ongoing check that a good unit stays a protecting one.