LEV Testing · Reading
From the metal fabrication shops to the engineering, joinery and finishing units about the town, Reading workplaces raise fume, mist and dust that the law says must be controlled - and the control proven by a thorough examination and test.
Reading has a working edge behind its Thames Valley offices. Its industry gathers on the trade parks about the town, where metal fabrication, engineering and food units sit alongside the joineries and finishing trades that serve Berkshire. Every one of them raises something a worker should not breathe - weld fume, grinding dust, oil mist, wood dust or solvent.
Local exhaust ventilation is what captures it at source, and the law does not take the control on trust. Under COSHH the extraction has to be thoroughly examined and tested at least every 14 months, measured against how it is used - not just switched on and assumed to work.
CNC and manual machining raises oil mist and metal dust at the enclosure and bench that has to be captured at source.
Flour, powders and steam need capture at the mixing and process points, from bakeries to production kitchens.
Saws, sanders and routers throw fine wood dust that has to be drawn off at the tool and the bench.
Weld fume and grinding dust need capture at the arm and booth, wherever steel is fabricated.
Bodyshop spray booths and prep bays carry paint mist and solvent vapour that the extraction has to hold and clear.
Fume cupboards, safety cabinets and dental and salon extraction all count as LEV and all fall due on the same clock.
Real jobs, described by sector and area - never by a client's name.
At a family-owned metal fabrication shop in Reading, the weld-fume arms over the welding bays had lost capture and the shop was hazing over by mid-shift. We measured capture velocity at each arm, checked the ducting and the filter condition, and found two arms below capture and a loaded filter dragging the fan. We set out the remedial action, and re-tested to confirm the control before certifying.
At an engineering unit in Reading, the mist extraction over the CNC line had dropped off and the bench capture felt weak. We measured capture and face velocities at each point, checked the ducting and discharge, and reported exactly which point fell short and why - so it could be put right and re-tested before certifying.
Condition of hoods, ducting, filters and fan - the damage, blockage and wear that quietly drops performance.
Measured capture and face velocities at the working points, plus transport velocity and static pressure through the system.
The readings assessed against how the LEV should perform to actually control the exposure - not just whether the fan turns.
Where the process warrants it, sampling to confirm the control is keeping the substance out of the breathing zone.
The point of a thorough examination and test is to prove the extraction still controls the exposure - so we measure it, we do not eyeball it. Condition, capture and face velocities, transport velocity and static pressure are checked against the design intent under HSG258, and the result is written up and labelled on the plant.
We test to the HSE's guidance, HSG258, and the job ends in a report and a label on the plant: what was measured, what passed, what needs putting right, and the date the next test falls due.
We examine the hoods, ducting, filter and fan and identify how each is meant to control its process.
We record capture and face velocities, transport velocity and static pressure at every key point.
The readings are assessed against the design intent under HSG258, with a clear verdict on control.
The plant is labelled with the result and next-due date, and you get the report for the COSHH file.
At least every 14 months under COSHH Regulation 9 - and sooner for certain higher-risk processes. We set the right interval for what you run and put the next-due date on the label and the report.
A thorough-examination-and-test report against HSG258, a pass/fail on each point with any remedials listed, and a dated label on the plant showing when the next test falls due.
We set out exactly what failed and why - often a single reading such as static pressure or capture velocity - so it can be put right, and we re-test to confirm the control before certifying.
Yes - the town trade parks and the town's units, and across Reading and the wider Berkshire.
No - any LEV: welding fume arms, wood and grain dust systems, spray booths, mist extraction, fume cupboards, and dental and salon extraction all fall under the same duty and the same clock.
Reading grew on the exact processes of its great works - the ovens of Huntley & Palmers, the coppers of Simonds' brewery - and the same instinct for measured control runs through the town's fabrication, engineering and finishing shops. Every one carries a duty to control the fume, mist and dust its work throws off - and to prove it with a measured test.
We have carried out LEV thorough examination and testing to HSG258 since 2001, across Berkshire and the UK. From a machine shop to a joinery, a spray booth or a lab fume cupboard, the job ends the same way: measured readings, a clear verdict, and a label whose next-due date you can rely on.
Tell us what you run and we will examine, measure, report and label it to HSG258 - across Berkshire.
